My Cart

Tip of the Month

July: Floor Maintenance

Maintaining polished and coated concrete floors improves their durability, enhances non-slip characteristics, assures an optimal level of performance and keeps them looking great. Any dirt and debris on polished or concrete floors acts as an abrasive. It will scratch the finish causing floors to look dull and lose durability over time. When you add traffic to these dirty floors, deterioration happens even quicker.

Below is a floor maintenance white paper that goes through some general tips to use when cleaning your floors along with before, during and after cleaning procedures to get the maximum results. Also, below here is a link to the online catalog where you can find more information on maintenance products and equipment.

June: Americans with Disabilities Act (ADA) Compliant Sidewalks

The Americans with Disabilities Act (ADA) is a civil rights law created to enforce a set of guidelines to ensure access to the built environment for people with disabilities. In Section 303: Changes in Level, it states that concrete slabs that are offset by more than ¼” in elevation are non-ADA compliant. To fix this and be ADA compliant, a permanent slope not steeper than 1:12 (1 inch of rise for every 12 inches of horizontal length) is required. The recommendation is a permanent fix of 1:16 to 1:20.

An epoxy mortar ramp to bridge the two offset slabs is a permanent solution that can be completed by your in-house maintenance team or your local QuestMark crew.

The steps for completing this project are as follows:

1. Saw cut the lower slab where the ramp will terminate and key in the edge.
2. Clean and vacuum any debris.
3. Prep the epoxy mortar by mixing part A and B together. Once fully mixed add the sand and mix well until there is even distribution of all parts.
4. Lay the mortar and trowel feeding into the terminations for a smooth and gradual transition.
5. Clean the edges and rope off until fully cured.

To identify shortcomings in ADA compliance regarding sidewalks and other accessible areas, QuestMark can help by completing a written analysis of your current conditions along with recommendations for corrective actions if needed.

To learn more about the epoxy mortar solution, watch our video or read more on the product.

May: Joint Filler

Create a seamless surface by filling any cracks, expansion joints or control joints throughout your floors. Having a seamless surface will help eliminate any dusting from your concrete floor, keep your floors cleaner and safer by minimizing trip hazards.

QuestMark’s Concrete Joint Filler is a do-it-yourself product that will help you repair and fill any cracks, joints or concrete defects on horizontal surfaces. It is easy to use, durable, flexible and quick curing. The joint filler is tack free in just three minutes and able to withstand foot and vehicle traffic in one hour.

Directions for use are simple:

1. Clean cracks or joints removing all dirt, oil, dust or other debris.
2. Ensure cracks or joints are clean and dry prior to application.
3. Load joint filler into cartridge gun or if using bulk product, mix using a 1 to 1 ratio pump.
4. Apply joint filler.
5. Scrape or peel any excess cured material from repair area.

Here is a short video showing the application of the product. To purchase Joint Filler or to learn more, click here.

April: Safety...A Top Priority

Workplace safety is a top priority for most organizations. We can’t take it for granted that our workplace environment is as safe as it could be for our customers, employees and vendors. Many organizations do safety training with their employees on a regular basis. However, does this include regular safety inspections or audits to ensure your workplace is as safe as it should be? You might be inspecting your equipment, processes and procedures but are you also reviewing your roof, floors and exterior surfaces? Do you know what to look for if you are inspecting these areas?

As a resource, CentiMark can help you by performing inspections and providing condition reports for your roof, floors and exterior surfaces. We will review your areas and note any needed repairs, safety hazards along with recommendations on solutions or safety accessories that will allow you to meet all OSHA standards.

Workplace injuries from slips, trips and falls (STF) can be very costly. One of the most frequently reported workplace injuries are a result from a STF. STF’s account for approximately 25% of reported claims per year and 15% of accidental deaths, second only to motor vehicle accidents. (United States Department of Labor) In most cases these incidents could have been prevented.

Check out these additional tools to see how CentiMark takes safety seriously.

Have a representative contact me to Book a Demo
Thank You
Thank you for requesting a demo of our $1 products. You have taken the first step in identifying which solution will best fit your needs and environment.